Vacuum Pump Maintenance
Installation and Maintenance SOP
Vacuum Pump Installation and Maintenance for Vacuum Gold Bar Making Machine
The vacuum pump is one of the key systems in a vacuum gold bar making machine. Correct installation, oil level control and daily maintenance help the casting chamber reach stable vacuum pressure and prevent pump oil emulsification, oil spraying and overheating.
This guide is written for operators who need a practical SOP for vacuum pump connection, first start-up, oil replacement and troubleshooting during gold silver bar casting production.

Short Answer
What should operators check before running the vacuum pump?
Before starting production, confirm that the pump is placed on a stable surface, the oil level is within the correct range, the vacuum hose is tightly connected, the exhaust port is not blocked and the machine voltage matches the pump nameplate.
If the vacuum pump oil turns milky yellow, sprays from the exhaust port or drops quickly below the normal oil level, stop long-time operation and replace the contaminated oil before the pump overheats.
Operator rule
- Do not run the pump for casting production before adding vacuum pump oil.
- Do not overfill the oil above the MAX mark.
- Do not block the exhaust port during operation.
- Do not continue production when the oil is emulsified or heavily contaminated.
Installation Checklist
Before installation: inspect the pump, oil and vacuum connection
First Start-Up Procedure
How to start the vacuum pump for the first time
1. Start without casting load
Run the pump briefly before production. Listen for abnormal noise and check whether the oil window is stable. This helps find wiring or hose problems before molten metal is involved.
2. Watch the vacuum gauge
The vacuum value should drop smoothly when the chamber is closed. If the vacuum value does not move, check the pump direction, hose connection and chamber sealing.
3. Check oil mist and leakage
A small amount of exhaust mist can appear during operation, but visible oil spraying or continuous leakage means the oil level or oil condition needs immediate inspection.
Maintenance Steps with Photos
Common vacuum pump oil problems and maintenance method

Oil leakage or oil spraying from the exhaust port
When the vacuum gold bar making machine runs for long daily production, moisture and oil contamination can cause oil mist, oil spraying or leakage at the exhaust port. If this continues, the pump may lose lubrication and overheat.
- Stop long-time operation and check the oil window.
- Check whether the oil level is above the MAX mark.
- Replace oil if the color is milky, dark or mixed with water.

Milky yellow oil means oil-water emulsification
During vacuum cycles, moisture can enter the pump and mix with the oil. When the pump heats up, water vapor expands and pushes contaminated oil toward the exhaust port. This is a common cause of oil spraying.
- Do not keep using emulsified oil for production.
- Drain old oil completely before refilling.
- Run a short test after replacement and observe oil color again.

Drain contaminated oil and refill clean vacuum pump oil
Use the oil drain port to remove contaminated oil. After draining, close the drain port tightly and add clean vacuum pump oil from the filling port. For high-frequency refinery operation, check oil condition regularly and replace oil before the pump performance drops.
- Prepare a container for old oil before opening the drain port.
- Do not mix different unknown oils during refilling.
- Wipe the pump surface clean after maintenance to identify new leakage.

Keep oil level between MIN and MAX marks
Overfilling is one of the most common reasons for oil leakage. Underfilling can reduce lubrication and damage the pump. Check the oil level when the pump is stopped and placed flat.
- Oil should not exceed the MAX line.
- Oil should not drop below the MIN line.
- After refilling, run the pump briefly and check the level again.
Troubleshooting
Vacuum pump troubleshooting table
| Problem | Possible Cause | What to Check | Recommended Action |
|---|---|---|---|
| Vacuum cannot reach required level | Air leakage, loose hose, chamber seal issue or dirty pump oil. | Vacuum hose, chamber gasket, inlet fitting and oil window. | Tighten connections, check sealing ring and replace contaminated oil. |
| Oil sprays from exhaust port | Oil-water emulsification, overfilled oil or long high-temperature operation. | Oil color, oil level and exhaust port condition. | Drain old oil, refill to correct level and test again before casting. |
| Milky yellow oil | Moisture has mixed with pump oil during vacuum cycles. | Oil sight glass and operating environment humidity. | Replace oil fully and shorten inspection interval in humid workshops. |
| Pump overheats | Insufficient oil, blocked exhaust, poor ventilation or long continuous operation. | Oil level, exhaust port and pump cooling area. | Stop the pump, allow cooling, correct oil level and improve ventilation. |
| Abnormal noise | Low oil, wrong oil, internal wear or foreign matter in the pump. | Oil level, oil type and running sound after startup. | Stop and inspect. Contact CDOCAST technical support if noise continues. |
Maintenance Schedule
Recommended vacuum pump maintenance interval
- Every production day: check oil level, oil color, pump noise and hose connection before casting.
- Every week: clean the pump surface and check whether there is new oil leakage around ports and seals.
- Every 150 operating hours: replace vacuum pump oil when the machine is used heavily in refinery or long-shift production.
- After humid storage or long shipping: run a short test and check oil color before continuous operation.
Do not open the vacuum system or oil drain port while the pump is hot, connected to power or under operating load. Let the equipment stop and cool down first. If the pump continues to leak oil after correct oil replacement, contact CDOCAST for technical inspection.
Related CDOCAST Pages
Related machine and process pages
FAQ
FAQ about vacuum pump installation and maintenance
Why does vacuum pump oil turn milky yellow?
Milky yellow oil usually means water has mixed with the vacuum pump oil. Moisture can enter during vacuum cycles and cause oil-water emulsification, especially in humid workshops or long production shifts.
Why does oil spray from the vacuum pump exhaust port?
Common causes include emulsified oil, overfilled oil, blocked exhaust or long operation with contaminated oil. Stop production, check the oil level and replace the oil if it is milky or dirty.
Where should the vacuum pump oil level be?
The oil level should stay between the MIN and MAX marks when the pump is stopped and placed flat. Too much oil can cause leakage, while too little oil can damage the pump.
How often should vacuum pump oil be replaced?
For high-intensity production, check oil condition every day and consider full replacement around every 150 operating hours. Replace earlier if the oil becomes milky, dark or contaminated.
What should I check if the vacuum value cannot reach the target?
Check vacuum hose connections, chamber sealing, inlet fittings, pump oil condition and whether the exhaust port is blocked. A small air leak can prevent stable vacuum during gold bar casting.
Need Technical Help?
Send photos or videos of your vacuum pump condition
If your vacuum pump has oil leakage, oil spraying, emulsified oil, abnormal noise or unstable vacuum pressure, send photos of the oil window, drain port, hose connection and vacuum gauge. CDOCAST can help identify the cause and provide maintenance guidance.
